Explainer

What is a good bounce rate for cold email?

Under 2% of emails sent, with hard bounces under 1%. Between 2% and 5% something is wrong with the list; above 5%, stop sending and fix the data before your domain pays for it. The fix is upstream: verified contacts, checked on the day you send.

Cold email bounce rate

We make Tamtam, and this page ends with where it fits. How we checked this page.

The short answer

A good cold email bounce rate is under 2% of emails sent, with hard bounces (addresses that do not exist) under 1%. Deliverability guides treat 2% to 5% as a warning to pause the worst segments and re-verify, and above 5% as the point to stop sending. Bounces are a data problem before they are a sending problem.

Hard bounces and soft bounces are different problems

A hard bounce is permanent: the mailbox, the domain or the route does not exist. It almost always means the contact data was wrong or stale. Remove the address after one clear hard bounce and never send to it again.

A soft bounce is temporary: a full mailbox, a server that is down, a rate limit. Retry a few times, and only suppress the address if the same mailbox keeps failing. Platforms label these inconsistently, so read the reply code if a number looks odd.

The thresholds, and what to do at each one

Two independent deliverability guides give the same bands. Use them per campaign and per sending domain, not across the whole account, or one bad segment hides inside a good average.

  • Under 1% hard bounces and under 2% total: healthy, keep normal hygiene
  • 2% to 5% total: pause the segments that bounce most and re-verify them
  • Above 5%: stop sending, suppress the bad addresses and replace the data source

Where Gmail and Yahoo rules fit in

Since February 2024, Google and Yahoo require bulk senders to authenticate with SPF, DKIM and DMARC, to offer one-click unsubscribe on marketing mail and to keep the spam complaint rate below 0.3%. Google counts as bulk a sender of more than 5,000 messages a day to Gmail accounts. Google and Close both advise staying under 0.1%.

Those rules are about complaints, not bounces. Both numbers still land on the same sending domain, and a list old enough to bounce is also a list of people who have not heard from you in a long time.

How to bring the bounce rate down

Verify on send day. People change jobs every week; an address checked when you bought the list may be gone when you send.

Treat catch-all addresses as their own segment. Verification cannot confirm a mailbox on a domain that accepts everything, so send to them in small batches and watch the result.

Fix the source, not the symptom. If one data vendor or one list consistently bounces above 2%, cleaning each export by hand costs more than changing where the contacts come from.

Where Tamtam fits

Tamtam works on the data side of the problem: each email is checked against the mailbox when you request it, after Tamtam has asked 35+ providers in turn, and you are charged only for a verified result. Tamtam does not send email, so it does not report your bounce rate, warm up mailboxes or manage SPF and DKIM: your sequencer (lemlist, Instantly and the like) does that, and those numbers live there.

Read next in the glossary

Frequently asked questions

Is a 3% bounce rate bad for cold email?

It is in the warning band. Find the segments that bounce most, pause them and re-verify before the next send.

Do soft bounces count?

They count in the total, but they are temporary. Retry them; suppress an address only if it keeps failing.

Do the Gmail and Yahoo rules apply to cold email?

They apply to bulk senders (for Google, more than 5,000 messages a day to Gmail accounts): authenticate, offer one-click unsubscribe on marketing mail and keep complaints under 0.3%. Authenticating your domain is wise at any volume.

What is the difference between bounce rate and spam rate?

Bounces are emails that could not be delivered. The spam rate is the share of delivered emails that recipients marked as spam. Google and Yahoo set their 0.3% limit on the second.

Fewer bounces start with the contact

Every email Tamtam returns has been checked against the mailbox at the moment you asked for it, so the list you send is the list that exists today.

“Before, I would spend 2-3 hours on account mapping. Today with Tamtam, I get it in 15 minutes.”
Joris PierrotData Marketing & CRM Manager @WMH Project

Trusted by 50+ EU and US revenue teams

How we checked this

We read 8 pages for this one, the original sources first (a vendor's own pricing or product page, the documentation behind a rule), and kept a fact only when two independent pages agreed on it. Every one was checked on 16 November 2026, and each links to the page we read it on below. We make Tamtam, so this page ends with where Tamtam fits. The explanation above it holds for any tool, and we say where Tamtam is not the answer. If something has changed, tell us at tamtam.ai/contact and we will fix it.

Last verified

Sources

  1. Apollo: a reasonable bounce rate benchmark with a paid data provider, as of 16 November 2026
  2. Suped: what is an acceptable email bounce rate, as of 16 November 2026
  3. Google: email sender guidelines, as of 16 November 2026
  4. Yahoo Sender Hub: best practices, as of 16 November 2026
  5. Close: requirements for bulk email senders, as of 16 November 2026
  6. Abstract API: how to verify an email address without sending one, as of 16 November 2026
  7. Tamtam Mobile Enrichment, as of 16 November 2026
  8. Tamtam FAQ, as of 16 November 2026

Information about other products comes from their public websites and review sites as of the date shown. Tell us if something changed: contact us.

Next step

See it on your own market.

Start a free trial and build your first list in minutes, or book a demo with the team.

Start free trialBook a demo

What you get with Tamtam

  1. 35+ data providers asked in turn for every contact
  2. Every email and mobile checked before your reps see it
  3. Contacts sent to HubSpot, Salesforce or lemlist